COADIS LINE 600TM Comfort units COANDA effect cassette teChniCaLdesCRiption Return/supply air interface ● Heater element feed on the terminalblock inside the VISUAL interfaces: Coanda effect diffusion via a single electrics box. narrow opening vent and specific internal profile. ● I t is possible to deactivate a heater element on site by means ● 2 models available: Visual 180 °or 360 °. of a shunt on the terminal to reduce the electrical power. ● I n sheet metal painted in RAL 9010 to be fitted over theCondensate drain pan chassis and exactly the same dimensions as a standard suspended ceiling tile. ● Single unit main pan in high-density sealed PSE for use in all ● Micro-perforated hinge-mounted metal return air grille withclimates, naturally sloped and removable from below without housing for EPURE function filter, opens fully without tools.the need to open the suspended ceiling. ● PSE insulation, M1 fire resistance with very low heat transfer● Fire rating: M1. coefficient. ● ABS PC auxiliary pan with no water retention provided as an ● An "anti-cold shower" system which is patented (filed underaccessory for the recovery of condensates from the valves No. 1451872) which prevents air from falling between theand coming from the main pan. two cassettes when they are aligned around the edges of● Gravity drain: height 70 mm. the room (only with Visual 180 ° diffuser). ● Drainage bushing: external Ø 15 to 20 mm. Casing Fan motor assembly ● Single casing and reduced size for all unit sizes, fits in place■ HEE motor of a 600 x 600 mm or 675 x 675 mm suspended ceiling tileLow energy motor making it possible to reduce electrical (option). consumption by up to 85%. ● Reduced weight compared to the previous generation ● Brushless technology. cassette. ● Sealed type, tropicalised with protected shaft. ● Ribbed galvanised steel motor support base panel, 10/10th ●3-speed gradual operation by 0-10V or on/off control signal , thick. without expansion board. ● High-density PSE casing integrating thermaland acoustic ●Internal normally closed series automatic overload protection functionalities. 15 mm base and 25 mm to 30 mm thick verticalon the windings. sides that make up the enclosure. ●"DFS" motor fault output using a photocoupler for potential ● Low emission of TVOCs and no halogenated compounds. alarm feedback via a Konnex protocol communication bus ● ABS corner reinforcements fitted with open galvanised one-(via the V3000 controller). way steel mounting brackets for assembly of threaded rods.● Mounted on anti-vibration mounts. ● Fire rating: M1. ● 230 V/1-Ph/50 Hz feed (6 Hz compatible).0 ● Hydraulic, air and electrical connections on the same side of the technical panel at the rear of the unit providing a singleNote: The minimum voltage to start up the motor is 2 V. access point. Or ● Finish frame in RAL 9010 galvanised steel,8/10th thick,■ Asynchronous motor housing the diffusion interface. 5 factory-wired speeds connected to a terminalstrip for ● Centring of the unit between the suspended ceiling profiles customisation. using anti-vibration elastomer mounts fitted on the finish● Sealed type, tropicalised with protected shaft. frame. ● Permanent capacitor. Water coil ● Roller bearings. ● 1 hot or cold water circuit (2-pipe system). ●I nternal normally closed series automatic overload protection ● 1 hot water circuit + 1 cold water circuit (4-pipe system).on the windings. ● Resilient mounts. ● Single piece sleeve with 40 mm centre to centre distance● 230 V/1-Ph/50 Hz feed (60 Hz compatible). with integrated sealed flush fitting female revolving unions,● High output and Displacement Power Factor (Cos Phi). for easy fitting of the control valves. ■ Fan(s) ● Low pressure drop one, two, or three layer circular coils. ● Copper pipes, one-piece aluminium fins (1.6 mm pitch).● Balanced centrifugal turbine Ø 282 mm with profiled blades. ● Purge and drain. ● Polymer turbine. ● Rated pressure 16 bar (at 20°C). ● Single point mounting system with foolproofing device. ● Test pressure 24 bar. Electrics box ● Max. hot water inlet temperature: - 4-pipe application: 80 °C, ● Large ABS electrics box with supported hinge and closed - 2-pipe application: 70 °C, with a bolt. - 2-pipe/2-wire application: 55°C (min air flow rate: 200m/h).3● IP20 Index of Protection. ● Min cold water inlet temperature: 6°C. ●Electrical connection terminal on DIN rail in compliance with Electrical heater (2-pipe + electric EN 50022, 7.5 mm deep. ● Marked out terminal strip with spring connectors. 0.5 to 2.5 mm² system) cross section - Max. current: 24 A – Shock resistance: 8 kV. ● 230/1/50 single-pipe electricalelements inserted into theCable grommet for field connection. aluminium housing. Fresh air supply sleeve ● 2 temperature limiters,manually and automatically reset,Connection sleeve for fresh air inlet, Ø100 mm, integral to the inserted in the aluminium block with easy access that does notframe with removable plug. require the suspended ceiling to be opened, via the Intake / outlet interface. 36 36 CATALOGUE 2021